Nanjing Ding Chun Electric Co., Ltd. Contact: Amaryllis light 18652048568 Business Phone: 025-66039810 Fax: 025-52797292 Mobile: 18652048568 Business QQ: 840422601 Business E-mail: 840422601@qq.com TM101 acceleration, velocity, displacement vibration protection table TM101-A00- B00-C00-D00-E00-G00-H00 TM101-A16-B00-C00-D00-E00-G00-H00 TM101-A06-B00-C00-D00-E00-G00-H00 TM101-A06-B01-C00-D00 -E00-G00-H00 TM101-A07-B00-C00-D00-E00-G00-H00 TM101-A07-B01-C00-D00-E00-G00-H00 TM101-A08-B00-C00-D00-E00-G00- H00 TM101-A08-B01-C00-D00-E00-G00-H00 TM101-A17-B01-C00-D00-E00-G00-H00 condition monitoring ★ absolute vibration monitoring of rotating machinery, such as chassis vibration, bearing vibration, machine frame vibration. ★ monitoring the rotor imbalance, misalignment, mechanical looseness, bearing damage, gear damage caused by vibration increases. Measurement parameters ★ vibration velocity, acceleration and displacement. ★ Unit Type A variety of rotating machinery. Such as fans, compressors, motors, pumps, gearboxes, turbines and the like. ★ particularly suitable for the technological transformation of the old units. Probe installation requirements ★ φ30mm only need to make a platform on housing, open a M6 screw, the probe is fixed to the screw holes on the inside of the machine without any operation. Specifications Electrical Specifications External Power (Pow er): 22-30VDC, 1 00mA, PC power supply, or use T M900; 90 ~ 220VAC power supply, 40 ~ 60Hz, 50mA. Frequency response: (± 3dB) Acceleration: 2.0Hz - 5KHz; Speed: 10.0H z-3KHz; displacement: 10Hz-3.0KHz; acceleration (low frequency options): 1.0Hz- 100Hz speed (low frequency options): 1.5Hz -100Hz; Displacement (low frequency options): 2.0Hz -100Hz. External sensor sensitivity (Sensor): 100 mV / g, 50 0 mV / g accelerometer; 4.0mV / μm / s, the speed sensor. External sensors: 24VDC, 4mA constant. Terminal: "A / P" terminal: Connect the red cable; "B / S" terminal: Connect the white cable. Buffered output (Buf Out): Output the original signal. DC bias: 10V DC; output impedance: Less than 500Ω maximum transmission distance: 300 meters. Sensitivity: the same sensor. Total vibration output (4-20mA): 4-20mA, active, drive 750Ω loads; 1-5V, active, output impedance 250 Ω. Alarm point setting (Normal / Set): Range: 0-100% full scale; Accuracy: ± 0.1%. Alarm Gain:> 60dB alarm relay (Alert / Danger): Seal: epoxy resin. Node capacity: 2A / 220V AC or 2A / 24VDC; resistive loads. Alarm Delay: 3 seconds node type: SPDT, SPDT. Output Isolation: 100 0VDC. Running photocell LED indicator: Green: The system self-test passes, the instrument is working properly; yellow: alarm indication; red: Interlocking instructions. Alarm reset / alarm bypass (RESET): Monitoring table built-in alarm reset button; remote alarm reset / alarm bypass terminals ("RESET").